XBOX 360 Repair Guide – #3 Installing the X-Clamp Kit
Wednesday, December 22nd, 2010 at
9:15 am
xbox360fixit.com You opened the case, prepared for the X-Clamp Fix, now your ready to install the X-Clamp Kit. Get the kit at xbox360fixit.com. If this video helped you fix your Xbox 360 please consider a donation. Follow this link http
@25skater4life did you put open your xbox? cause if you do your warranty will void and it can break when you do something wrong with something which is in the xbox
hey man i did everything you did and still dont work, now my fan stays on for like 1 minute then shuts off and now has 2 red rings. I turn the 360 on and then 3 red rings shows up and just after a minute it goes to 2!!! PLEAAASSSSSEEEEE HELP MEE IDK WHAT TO DO email me at bmxstreetrider787@yahoo.com
electrical tape?
how long does this usually work for?
thank you, this helped me alot!
@yellowstardust420 This is the same problem I’ve got. Tried loosening the bolts again twice now with the same results. I’m using #10 bolts with a panhead and rubber washers because I couldn’t find silicone. Couldn’t gt the repair kit, everything else worked fine for disassembly but now not so much. If you get an answer to this I’d appreciate the feedback.
hi
ive followed this video step by step and still have 3 red lights. i took it apart again, heat gunned it and used expensive thermal heat paste and still got 3 red lights.
any one know what else i can do apart from chuck it in the bin. xbox 360 peice of sh*t ill never by an xbox again its back to playstation for me…any ideas pm me its easier than looking through the message board for replys. any help would be appreciated thanx
i got two flashing red lights ant the fan keeps shutting down and it wont over heat. i followed the video step by step and it still didnt work. any ideas people?
i got two flashing red lights ant the fan keeps shutting down and it wont over heat. i followed the video step by step and it still didnt work. any ideas people?
this works. ive had to re-over heat it a few times but each time it works.
Hey, I wondering why Xbox doesn’t read the disc, Do u know whats problem is??How do I fix that.. would u please make a video for me pleassssseeeee??
I enjoy watching u do that videos. thx
well i did everything you said and when i got to the overheating step i turned on my xbox 360 and the fan didnt run i checked it multiple time and its plugged in. it works for a few seconds and turns off. What do i do please help
@xxovermetalxx like he said leave it for about 20mins to overheat.
@gjeni7 scotch tape
@reddragon9 just buy hes kit.
@fktheworld1 clamps are bullcrap made by microsoft. they bend your mother board when your xbox is hot
@sonnifer I was thinking to buy new xbox but first i thought… why dont i try to fix i old one first inplace of throwing it away, if shit happens i will buy new one. so id suggest you to first try and fix it then throw it away:)
Dont use nylon washers, because after one month they will melt a bit and flatten. that happened to me before
why would u take off the paste? its their for a reason to protect yr processor!
I don’t know if this is really worth it. I think I might just throw my xbox away.
I did this ages ago in september , but i used cheap crappy thermal paste off ebay will this matter and the xbox noew gets 3 red rings , Shall I do a Reflow with my Heatgun ?
thanks
hi i followed this video step by step and still have 3 red lightsany idea what i can do now?
Gotta tighten kitty-corner! Kitty-corner! Not in a circle!
i did what you said and after it cooled down i turned it on and only the center green light came on. nothing else will happen my controller wont sync or anything what do i do?
what if i put the clamps back on instead of screws??????